Granite Countertop Processing Note
1¡¢ Gross
procurement requirements in the 1.95-2.15 cm plate thickness .
2¡¢Procurement
- plate thickness in the 1.90-2.1 cm, 85 gloss over.
3¡¢ Large
cutting processes Note:
£¨1£© Stones
placed in the platform should be firmly and smooth.
£¨2£© To
understand them clearly see the big stone cutting segmentation diagram.
£¨3£© Under
the knife before cutting large size correction, to review carefully and
accurately.
£¨4£©Stone
cut the first three films, the first stop of the first percutaneous stone
tablets destroyed, the quality inspection Stone: whether dark crack, Glenn,
stain, the color line, and other quality defects;
Check whether the thickness of
the first three films within the allowed tolerances (20 mm ¡À 5mm), and to give
timely amendments
£¨5£© Machine
operators do before and after inspection, cleaning and maintenance, cleaning
work.
£¨6£© Meeting:
thickening plate with the best cutting edge (height), in particular on a texture
of the stone.
4¡¢ For
thick processes Note:
£¨1£© Thick
End determining the actual thickness of 19.5-2.0 cm. Review by vernier caliper
thickness.
£¨2£© Operation
should carefully. Raising release sheet to the attention of safety and avoid
damage to sheet metal.
£¨3£© Machine
operators do before and after inspection, cleaning and maintenance, cleaning
work.
5¡¢ Large
polished processes Note:
£¨1£© Polish
post-meeting before plastic, stone plate (especially granite) crannies filled
out and avoid spent many wait until the finished human beauty fill in the
plastic.
£¨2£© Polish
abrasive process used to set resin polish.
£¨3£© Gloss
over 85.
£¨4£©Raising
caving plate to avoid inadvertently damaged sheet metal
£¨5£© Leftover
parts to wear that enough to gloss
6¡¢ Bridge
shear processes Note:
£¨1£© To
smooth upward cut.
£¨2£© Saw
blade to sharp. (Knife before the first head wear sharp)
£¨3£© To
control under the knife and cutting good speed.
£¨4£© Have
Machining Allowance. (Cushion to 3-4 mm for 1 / 2 yen at the seams stereotypes
stereotypes to within 0.3 mm).
£¨5£©there
is texture of the stone to a cutting edge even thickening out with such textural
Large thickening of the texture edge to be fair, finished only beautiful
natural. (Set a number, and if there are patterns even when the direction of
direction).
£¨6£©To
avoid missing Prism, missing Kok, not completely cut off, cutting distortions,
such as the wrong size phenomenon
£¨7£© Machine
operators do before and after inspection, cleaning and maintenance, cleaning
work.
7¡¢Gluing
stereotypes processes:
£¨1£© Palette
carefully, as far as possible will be redeployed to the basic and plastic stone
color consistency.
£¨3£© Before
gluing matched the best selection of sheet metal contacts for bonding.
£¨2£© Thickening
of the plate and a plate to keep secret. A dense, using metal clip, fixed, and
let it laminated.
£¨4£© After
the completion of glue joints is not more than 0.3 mm.
£¨5£©In
bonding, it is necessary to pay attention to the glue No, it is necessary to
stem excess glue shaved his, avoid refined beauty, flowers in many human on
scraping gum.
8¡¢ 1
/ 2 Circle stereotypes processes Note:
£¨1£© Because
of the Machining Allowance (3-4 mm), to 1 / 2 yen Machining Allowance than the
original when no more than 3-4 mm deep set, glue joints after not more than 0.3
mm.
9¡¢ Hand
processing that processes Note:
£¨1£©50
degrees angle radians.
£¨2£© That
should be as far as possible, smoothing over natural corner. The surface should
be formed.
£¨3£© Careful
handling to avoid damage to granite countertop.
10¡¢ Small
polished surface processes Note:
£¨1£© Sheet
metal or wooden size metal frame that came to the put away and avoid injury
Taiwan panel edge in order to maintain angular integrity.
£¨2£© Gloss
over 85.
£¨3£© Small
surface grinding have to be carefully and comprehensively. Straight to
straightening curves to smooth over-natural, corner of the mill to place.
£¨4£© Phase
angle or excessive wear to the Department should not feel without scalloped
feeling edge grinding to a little hands will not scratch.
11¡¢ Fill
plastic cosmetic procedures Note:
£¨1£© Stone
should be placed in strict accordance with the names, color Division, placing
neat and orderly manner. Open, the need to fill plastic edge in the same
direction, forming a straight line. This ease of effective, rapid and accurate
fill plastic beauty.
£¨2£© Palette
carefully, as far as possible will be redeployed to the basic and plastic stone
color consistency.
£¨3£©
To master the glue dry time. Avoid
too dry scraping
can not glue or glue not disturbed, even plastic scratch.
15¡¢This
"granite countertop processes processing diligence" by the quality control staff
circulated to a Road processes.
£¨5£© No
haphazard display, all kinds of stone mixed together.
£¨6£© Fill
plastic staff by a color stone varieties or division positioning.
£¨7£©Fill
plastic End, we should clean up the venue. Tools placed neatly.
12¡¢Note
removal process (the procedures required attention, in particular the forklift
Handling)
£¨1£©102
mm retaining plate on the prototypes, no-placed.
£¨2£© Smooth
to-face display.
£¨3£© Use
of soft-bonding (such as foam) back pad. Avoid scratches the surface. .
£¨4£© Forklift
removal process should be careful, take the necessary protective measures to
avoid forklift encountered obstructions or uneven pace of sheet metal fell,
damage.
13¡¢ Packaging
processes Note:
£¨1£©
By leveraging the wooden box packaging
exports.
£¨2£© Located,
moving to be careful and meticulous
£¨3£© Face-to-face
emissions. Middle use styrofoam / foam / plastic separated to avoid surface
damage.
£¨4£©A
firm producing wooden box; Wooden box to needle firmly.
14¡¢Finished
processing all daily operations to maintain work sites clean, tidy and health.
£¨4£© Fill
plastic should be careful to avoid inadvertently unification, the sheet metal
stamping on the break. No sitting on the sheet metal fill plastic operations.
